MAINTENANCE PLANS FOR YOUR HEATING AND COOLING SYSTEMS

We service & install many major brands of heating and cooling home comfort systems to accommodate all residences and budgets. This includes oil tanks, humidifiers, water heaters, and any indoor air comfort and quality systems.

Personalized Service

Thank you for your interest in Hillside. We’re a full-service heating, air conditioning, and fuel delivery company that has been family owned and operated for over 60 years. We proudly service all of New Castle and Cecil Counties and parts of Chester County. Our attitudes and commitments at Hillside strive to be those of customer satisfaction. We’re people too and know how we’d like to be treated when we are customers.

Air Conditioner and Heat Pump Maintenance Plan

HVAC Tune-Up Includes the Following:

• Clean condenser coil and indoor coil (where accessible)
• Oil and inspect motors
• Inspect wiring and tighten electrical connections
• Check capacitor and contactor
• Check and change air filter (customer supplied)
• Clear condensate drain line
• Inspect refrigerant line connections
• Check system refrigerant charge and thermostat for
  proper operation
• Check amp draw of the compressor, condenser motor, and
  blower motor

Covered Parts/Services:

Hillside’s maintenance plan for central air conditioning and heat pumps offer a percentage discount on all billable service based on your plan. Non-covered parts are billed at regular service rates.

Labor 7 days/week, 8:00 a.m. – 8:00 p.m. including Holidays

Same Day Emergency Service:

Download Hillside’s Air Conditioner and Heat Pump Maintenance Plan

• Low-Pressure Switch
• Run Capacitor
• High-Pressure Switch
• Start Capacitor
• Condenser Motor
• Condenser Fan Blade
• Contactor
• Blower Control
• Blower Motor
• Blower Belt
• Air Handler Circuit
• Board
• Relays
• Transformer
• Condensate Pump
• Wiring, Motor Protector
• Condensate Pan
• Hard Start Kit

Parts & Services Not Covered: Ductwork, cabinets, insulating material, main power service and electrical wiring, indoor air quality products (i.e. humidifiers, electronic air cleaners), system accessories or enhancements, grill registers, diffusers, failure in physical appearance such as scratches, dents, rust, ect., refrigerant systems using other than R22 or R410A, any other part not included in the original manufacturer of the system, freight, units over 5 ton (60,000 btu), commercial units, rooftop units or hanging units.

Heating Maintenance Plan

Heater Tune-Up Includes the Following:

• Replace nozzle one oil filter, and pump strainer
• Clean, lubricate, and adjust burner, inspect all controls and adjust if needed
• Vacuum and clean boiler or furnace, smoke pipe and base of chimney (Where needed and accessible)
• Inspect and clean combustion chamber – Oil circulating pump or fan motor and bearings
• Clean and adjust electrode and high-tension leads
• Check pump, examine belts, pulleys, and couplings

Warm Air Systems:

Percentage of coverage based on plan for parts and labor associated with repairs or replacements of defective parts (as listed below) due to normal wear and tear for one year from date of acceptance. Parts not specifically listed are not covered. If replacement of equipment becomes necessary, or customer decides to upgrade, Hillside will credit the amount of this maintenance plan toward a replacement performed by Hillside. It is the customers’ responsibility to call and schedule annual tune-up to keep furnace in an operating condition.

Download Hillside’s Heating Maintenance Plan

• Electrodes Nozzle
• Pump strainer
• Fan & limit control
• High tension lead
• Oil burner motor
• Draft regulator
• Combustion Chamber
• 1 Thermostat (Plain)
• Drive Couplings
• Smoke pipe-10’
• Shaft/bearings
• Transformer
• Fuel oil pump
• Fuel oil filter
• Primary relay
• Burner fan
• Blower motor
• Blower belt

Warm Air Systems:

All parts covered in warm air system plus: Feed Valve, Relief Valve, Aquastat, Circulator Motor, Drive & Bearing Assembly An extra $20.00 is charged for each additional circulator.